Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Parts & Accessories

$2.50 - $22.99
Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.
$44.99
Everything you need to fully rebuild your OneUp Aluminum Pedals. Our V2 kit is compatible with all OneUp Aluminum pedals. The brass bushings take the place of the 3 small cartridge bearings and aluminum washer that were on our original pedal assembly. KIT CONTAINS - 2 LARGE OUTER BEARINGS - 2 BRASS BUSHINGS - 2 OUTER SEALS - 2 FLANGE WASHERS - LH AND RH AXLE BOLTS - 2 AXLE O-RINGS - LH AND RH BEARING NUTS
$44.99
Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees
$35.00
Replacement charging clips and Y-shaped cable for the POWRLINK ZERO Power Pedal System In the box - Y-shaped charging cable - Charging clips (x2)"
$33.00
- The ATAC 13/17° cleat works with all TIME mountain pedals. - Included with all mountain pedal models numbered "6" and higher - Release angles of 13 degrees or 17 degrees depending on how the cleat is set up on the shoe - Compatible with all two-hole cycling shoes.
$33.00
- The ATAC EASY 10° cleat works with all TIME mountain pedals. - Included with mountain pedal models numbered "2" and "4." - Release angle of 10 degrees and is compatible with all two-hole cycling shoes. - Don't let the "Easy" name fool you. If you are a high-performance rider looking to reduce the release angle from our 17 or 13 degrees, this is the choice for you.
$33.00
- Works with all XPRO and XPRESSO pedals. - Not included with new XPRO and XPRESSO pedals. - This is a zero-float cleat design, so there are zero (0) degrees of heel float and no lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.
$33.00
- Developed for the TIME XPRO & XPRESSO road bike pedal range. - They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. - You can also adjust the Q-factor (by switching the cleats) - The Bi-material brings more durability when walking with the cleats. - These cleats are the stock cleats included with all XPRO & XPRESSO pedals.
$33.00
- Works with all RXS and Impact pedals. - Five degrees of heel float and 2.5mm of lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.
$33.00
- Pedal Grip pins/bolts and 4 tension screws TIME SPECIALE 8/12
$25.00
- Pedal Carbon blade Kit TIME XPro QTY 4
$49.00
- Pedal Body Cover Cap Left/Right TIME Xpresso Black including screws
$35.00
- Pedal Cover Cap Left/Right Top replacement TIME XPro
$54.99
Pedal Axle Rebuild Kit for SPIKE & OOZY Trail Pedals - 1 set L&R axle - 2pcs IGUS bushing - 2pcs O-ring - 2pcs dust cap - 2pcs stainless shim washer - 2pcs silicone friction seal - 2pcs lock nut
$11.99
IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer
$8.99
Shorter 7mm rear load pins for the outer extremities of SPOON, SPIKE, and OOZY pedals. - Provide durability and improved safety - Mix and match with the longer stock pins to customize your ideal amount of grip
$49.99
- Crank boots compatible axle rebuild kits for SPIKE and OOZY pedals (with bright green friction seals), produced in 2015 or later. Bearings must be purchased separately. - Crank boots compatible axle - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs
$11.99
Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included
$63.00
The Spoon Pedal Axle Rebuild kit includes the internal parts required to completely rebuild a set of Spoon pedals. - Pins available separately
$71.00
Our rebuild kit keeps your Daemon pedals running like new. Includes: - Nitrox-coated axles (left and right) with nuts (x2) - Stainless steel, sealed Enduro cartridge bearings (x4) - Igus bushings (x2)
$28.00
Replacement pins for our Daemon pedals: - 5mm long - Made with 316 stainless steel - Precision CNC Machined in Whistler, B.C. - Sold in packs of 10
$33.99
- Allows a customer to replace their cleats. - Two replacement cleats in box
$39.99
- Woven nylon fiber material - Double hold system for strength - Durable for urban or MTN riding - Fits most BMX platform style pedals - Anti-slip adjustable design
$14.99
Nylon toe clip straps, with zinc-plated steel quick-release buckles.
$14.99
- Strapless resin construction - Strapless design - Tough and lightweight, ideal for urban conditions with frequent stops
$14.99
- Double tongue resin toe-clips - Nylon straps with steel buckles
$24.99
- Strapless design is easy to engage without fully committing to the pedal - No special shoes required - Improves pedaling efficiency - Molded from unbreakable nylon - Please make sure your pedals have visible mounting points or a removable reflector for mounting prior to purchase - Includes mounting hardware. Note: metal plate may not be required during installation.
$19.99
Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
$37.99
Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals
$10.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
Page 1 of 2 Next page